8000W Prewired IPS Dual Board with System EnclosureSKU: BRC-4000WM2
Pre-wired and Fully Tested
Our off grid boards are pre-wired in our warehouse, and tested before we have them shipped to you.
Save Time With On-Site Installation
Because our off grid boards are pre-wired, you'll save precious time installing your system, or buying extra items you did not expected to need.
Meets Australian Standards
This complete off grid board is assembled according to the current Australian Standard.
Save yourself time, money and hassles when installing your next off grid system!
Our off grid boards are built with everything you need for an off grid system in a pre-wired format that is easy to install. This pre-wired system saves you precious hours of on-site installing, and avoids the discovery that you need extra parts you don’t have on hand. Pre-wiring also ensures that all components are functional and ready to go.
Our boards focus around the Integrated Power System (IPS) unit that provides the inverter, solar controller, and battery charger. The IPS is wired with cabling, breakers, fusing, and everything else that is required - all according to current Australian standards. Each board is tested prior to being sent, avoiding faulty components upon delivery. Once the board is on site, installation is as easy as connecting the battery bank and solar, and having an electrician wire it to the main board.
Important Note: AC output (for inverter 240V from the unit) requires hard wiring, and for safety reasons will need to be installed by a qualified electrician. PV may be installed by a competent person if using extra low voltages, otherwise this will also need to be installed by a qualified electrician or off grid installer.
- 2x Giant Power 48V 4000W Integrated Power System
- 1x Giant Power Vermin Resistant System Enclosure
- 2x Integrated Power System Parallel Kit
- 4x AC 32A Breaker Single Pole
- 4x Miniature Circuit Breaker 2 Pole DC 32A 500V
- 2x 9 Pole Enclosure
- 2x 6 Pole IP65 Enclosure
- 1x HRC Enclosure NT1
- 3x HRC Fuse 250A NT1
- 1x HRC Enclosure NT00
- 2x HRC Fuse 160A NT00
- 1x Meter A/C - kWh Din Rail Mount
- 1x Generator Input Plug
- 1x Sticker - Solar Safety Label Kit
- 1x Sign - Warning Spark Hazard - Metal
- 1x Sign - Electrolyte Burns - Metal
- 1x Form Ply 1200 x 800
- 1x Board Wiring & Sundries
No product reviews yet - be the first!
|IPS 4000WM Prewired Dual System Board Enclosure|
|Dimensions||1500mm x 620mm x 380mm|
|Giant Power 48V 4000W Integrated Power System|
|Nominal DC Voltage||48V (MAX 60V)|
|Transfer Time||<10ms (UPS mode)
<20ms (Appliance mode)**
**Transfer time may be longer (30ms) when used in parallel configuration, and this may cause interruption for certain loads
|No Load Power Consumption||<50W|
|Power Saving Consumption||<15W|
|Surge Rating||8KW (5 seconds max)|
|Output Waveform||Pure Sine Wave|
|Output Voltage||230VAC +/- 5%|
|Output Regulation||< 3% RMS for battery voltage range|
|Output Short Circuit||Circuit Breaker|
|AC Battery Charger|
|Boost Voltage||58.4V (Flooded)
|Float Voltage||54.0V (Flooded)
|AC Recharging Current||60amp (adjustable)|
|AC Input (Mains/Generator)|
|Input Power Factor||0.8|
|Input Voltage Range||90~280VAC (Appliance mode)
170~280VAC (UPS mode)
|Solar Charge Controller|
|Type||Maximum Power Point Tracking (MPPT)|
|Max Charging Current||60 Amp|
|Max PV Input/Output||3000W|
|Max PV Input Voc||145V|
|Environmental / Mechanical|
|Temperature Range||Operating: 0oC ~ 55oC
Storage: -15oC ~ 60oC
|Operating Humidity||20~90%RH Non-Condensing|
Specifications for all other components are available upon request.
For more information, please read our full warranty policy